SIG100 IC - UART/LIN TRANSCEIVER IC OVER DC POWER LINE

The next Generation byte oriented powerline transceiver - up to 115.2kbit/s

The SIG100 IC merges both data and power over the power line, eliminating the need for control and data wires. The SIG100 is designed to meet the new DC-LIN ISO 17987-8, providing a seamless interface with LIN-BUS networks.

SIG100 powerline communication IC
Description

The SIG100 IC modulates UART/LIN bytes over the DC powerline (DC-BUS).  The SIG100 is an advanced generation of the widely used SIG60 device. Both devices use a unique multiplex digital signaling technology that overcomes the powerline noisy environment at bitrates up to 115.2Kbit/s.   A Sleep mode allows low power consumption when the device is not used.

The SIG100 power line UART transceiver reduces wiring in Automotive, Aerospace, Industrial, Lighting, Sensors, Actuators, Battery management systems (BMS), Climate control, Truck-Trailer communication, etc.

  • SIG100 powerline transceiver Building Blocks

Operation

The SIG100 IC operates as a Master-Slaves UART network of multiple SIG100 ICs. Users can define their protocol since there is no limit to the number of UART bytes in a message. Furthermore, the SIG100 operates on any selectable carrier frequency between 5MHz and 30MHz with 100 kHz spacing, allowing multiple independent networks to coexist on a single powerline by using different carrier frequencies for each network.

The Figure below depicts a typical SIG100 network, demonstrating a single byte transmission from a SIG100 TX device to three SIG100 RX devices coupled through a capacitor to the same powerline. Upon detection of a start bit on the  SIG100 TX device HDI pin, a modulated PLC-byte transmission starts.  Then, the modulated PLC-byte is decoded back to a byte-field on SIG100 RX ICs' HDO pin at a fixed latency of ~2.5 bits.

SIG100 byte-oriented network example.

  • SIG100 Powerline Network Example
TYPICAL SCHEMATIC
  • SIG100 PLC Typical Schematic

TECHNICAL DOCUMENTS

Features

  • Noise robust UART / LIN over battery power line transceiver.
  • No limit to the number of bytes in a message.
  • 251 selectable carrier frequencies between 5MHz to 30MHz.
  • Selectable bit rates between 9.6 Kbit/s to 115.2 Kbit/s.
  • Operates as Master or as a Slave in a multiplex network.
  • Designed to meet DC-LIN ISO 17987-8
  • Hard-coded 48 bit UUID.
  • QFN 32 small footprint pins package
  • Sleep Mode for low power consumption.

Applications

  • Vehicles LIN-BUS
  • Battery management (BMS)
  • Climate control network
  • Sensors / actuators bus
  • Robotics control networks
  • Lighting control
  • Truck-Trailer communication
  • Multiple networks sharing the same powerline.

Pricing

  • 1 - 49                       $6.30
  • 50 - 99                     $4.99
  • 100 - 999                 $4.37
  • 1000+         Contact Us

Pricing

  • 1 - 49                       €6.30
  • 50 - 99                     €4.99
  • 100 - 999                 €4.37
  • 1000+         Contact Us

Payment

  • Money transfer to Yamar's bank account
  • Credit Card (Visa/MC/AMX) + 2.7%

      • CONTACT US

      Privacy Policy

      Related products

      DC Power Line AttenuatorRead more +18 September 2018 By admin in , ,

      DC Power Line Attenuator

      DCB1M Test SoftwareRead more +18 September 2018 By admin in , ,

      DCB1M/SIG100/SIG102/DCAN500/DMX250 Test Program

      EVB TesterRead more +22 September 2019 By admin in , ,

      DC-BUS EVB Tester

      SIG102 powerline EVBRead more +24 September 2019 By yair@yamar.com in , ,

      SIG102 Evaluation Board

      SIG102 powerline IO deviceRead more +24 September 2019 By yair@yamar.com in , ,

      SIG102 IC – Multi I/O Control over DC Power line Network

      SIG100 EVBRead more +07 July 2020 By Eran Priel in , ,

      SIG100 Evaluation Board

        CONTACT US

        Privacy Policy

        YAMAR ELECTRONICS Ltd.

        A fabless semiconductor company since 1994. We develop and sell our unique devices for DC power line communication targeting wire saving. Customers in more than 51 countries use the devices in a wide range of applications; Automotive, Aerospace, Lighting, Battery monitoring (BMS) and more. The devices meet existing protocols such as UART, LIN, CAN, SPI, DMX512, and I2C keeping it simple to operate. Yamar engineers lead the LIN over DC powerline (DC-LIN) ISO 17987-8 standardization workgroup.

        The innovation team continues to develop new technologies and products.

         

        Sunday- Thursday 09.00 - 18.00

        PAGES

        WORLDWIDE

        TOP